Muhammad Iqbal

 

 

 

Newer HSDPA/UMTS/3G devices (USB dongles) from Option comes with a “packet interface” and requires a special driver, older cards should work just fine with ubsa(4), u3g(4) or any similar serial-over-USB driver.

The driver should support most new hardware from Option. The following
devices have been verified to work

• Option GlobeSurfer iCON 7.2 (2.4.6Hd firmware)
• Option iCON 225
• Option iCON 505
• Option iCON 452

If you have any other device (like iCON 031, iCON 210, iCON 315, iCON 322, iCON 401, iCON 431, iCON 451), please test and report. Thanks.
Note that the driver currently doesn’t recognize other devices, although most newer Option HSDPA devices should work. More devices IDs will be added as devices are found. If you own any newer Option device that appears as a USB device, please report back with the device ID.
Note: iCON 7.2 devices with older firmwares are supported by ubsa(4) if you add the correct device ID, or by the new u3g driver available in 8.0 or later. You have the old firmware the device ID of the mass storage device is 0×05C6 and changes when you switch the device.
Note: This is NOT for cards based on the Nozomi chipset.

FreeBSD 9/CURRENT

Included in BASE.

> kldload uhso

See uhso(4) and uhsoctl(1) for more information

FreeBSD 8

The FreeBSD 8 driver can be installed through FreeBSD ports. It’s available in comms/uhso-kmod

> cd /usr/ports/comms/uhso-kmod
> make install

FreeBSD 8 Driver – uhso-20100416.tar.gz
FreeBSD 8 Connection utility – uhsoctl-20100416.tar.gz

FreeBSD 7

Not that this version of the driver is unmaintained
The FreeBSD 7 driver can be installed through FreeBSD ports. It’s available in comms/hso-kmod

> cd /usr/ports/comms/hso-kmod
> make install

Please see hsoctl(1) for instructions on how to connect to your provider.
FreeBSD 7 Driver – hso-20081023.tar.gz
FreeBSD 7 Connection utility – hsoctl-20081023.tar.gz
option-iconf.conf for devd (automatic mode switching)
option-iconf.conf

Manual install

A simple make should do the trick. If the build would fail for some reason, make sure you have the latest tarball and that the usbdev patch was applied properly. If it still fails, send me a mail with the (whole) error message together with which FreeBSD version you are using.
The following is only required for FreeBSD 7
These devices are so-called ZeroCD devices that when plugged in appears as a mass storage device with windows drivers. To get the HSDPA interface the device needs to be switched, this can be done automatically with camcontrol and devd. The umass(4) driver must be present in the kernel or loaded as a module for this to work.
Add the following to a file called option.conf and place it in /etc/devd/ (create the directory if it doesn’t exits) then restart devd with /etc/rc.d/devd restart
Make sure you replace the product id (0×6911) with the one your device has, you should be able to get it with usbdevs -v
Note that this is optional, you can always switch the device manually using camcontrol or with a program called usb_modeswith.

Using the driver

Load the kernel module and plug in your device

> kldload uhso.ko

If the driver identifies your device you should see something like this

uhso0: <Network port> at <Option N.V. Globetrotter HSDPA Modem> on usbus5
uhso1: <Diagnostic port> at <Option N.V. Globetrotter HSDPA Modem> on usbus5

And a new network interface should have appeared

> ifconfig
hso0: flags=0<> metric 0 mtu 2048

In addition to this several TTY devices should have been created, you can figure out how many by using sysctl.

sysctl dev.uhso

Connection with the uhsoctl connection utility

The uhsoctl connection utility automatically creates and maintains a connection.
It will automatically set IP-address and default route, and update/etc/resolv.conf with the correct nameservers.
It can run both in background and in foreground mode. The execution syntax is hsoctl [options] interface, the following options are recognized (most of with are optional).
-a APN – Access point name
-p PIN – Specify device PIN.
-u username
-k password
-c PDP context ID
-r path – Path to resolv.conf (use /dev/null to disable)
-f path – Specify serial port device to use
-n – Do not fork into background (run in foreground)
-b – Fork into background directly (without waiting for a connection)
-d – Disconnect
Foreground example
Hitting CTRL-C will close the connection.

> uhsoctl -n -a bredband.tre.se -p 1234 uhso0
Searching for network (UMTS)
Registered to "3" (UMTS)
Connected to "3" (bredband.tre.se), carrier UMTS
IP address: 78.156.206.64, Nameservers: 80.251.192.244, 80.251.192.245
Status: connected (UMTS), signal: -87 dBm
^C
>

Background example

> uhsoctl -a bredband.tre.se -p 1234 uhso0
Searching for network (UMTS)
Registered to "3" (UMTS)
Connected to "3" (bredband.tre.se), carrier UMTS
IP address: 78.156.206.64, Nameservers: 80.251.192.244, 80.251.192.245
>
> uhsoctl -d uhso0
Disconnecting uhso0
>

Manual connection

Look up the serial ports

# sysctl dev.uhso
dev.uhso.0.netif: uhso0
dev.uhso.0.type: Network/Serial
dev.uhso.0.ports: 2
dev.uhso.0.port.control.tty: cuaU0.0
dev.uhso.0.port.control.desc: Control
dev.uhso.0.port.application.tty: cuaU0.1
dev.uhso.0.port.application.desc: Application
...
dev.uhso.1.type: Serial
dev.uhso.1.ports: 1
dev.uhso.1.port.diagnostic.tty: cuaU1
dev.uhso.1.port.diagnostic.desc: Diagnostic

Open one of them, for example the Control or Application port, in a terminal
application like minicom. Issue the following commands to establish a connection.

AT+CPIN="1234" # Your PIN
OK

AT+CGDCONT=1,,"bredband.tre.se"
OK

AT_OWANCALL=1,1,1
OK

AT_OWANDATA=1
_OWANDATA: 1, 95.209.79.126, 0.0.0.0, 80.251.201.177, 80.251.201.178, 0.0.0.0, 0.0.0.0, 72000

Configure the interface and set a default route

# ifconfig uhso0 95.209.79.126
# route add default -interface uhso0

Manual connection

Figure out which serial ports that
Open /dev/cuaHSO0.0 (or cuaHSO0.1) with a terminal program (for example minicom), baud rate doesn’t matter.
If your SIM card requires a PIN

AT+CPIN?
+CPIN: SIM PIN
AT+CPIN="1234"
OK
AT+CPIN?
+CPIN: READY

Next, configure the APN (you should have the details from your provider), you only need to do this once (or when you change APN).

AT+CGDCONT=1,,"bredband.tre.se"
OK

If a username and password is required, it can be specified with

AT$QCPDPP=1,1,"pass","user"

To create the connection, type

AT_OWANCALL=1,1,0

The LED on your device will stop blinking and get a steady shine when you’re connected.
Now, to get the IP info type

AT_OWANDATA=1
_OWANDATA: 1, 79.138.181.171, 0.0.0.0, 80.251.192.244, 80.251.192.245, 0.0.0.0, 0.0.0.0, 72000

The first address is your ip-address, the third and the fourth are your name servers. Now simply configure the network interface with this information as any other network connection.

> ifconfig hso0 79.138.181.171/32
> route add default -interface hso0
> echo "nameserver 80.251.192.244" >> /etc/resolv.conf
> echo "nameserver 80.251.192.245" >> /etc/resolv.conf

Your connection should be ready now

> ping ping.sunet.se
PING ping.sunet.se (192.36.125.18): 56 data bytes
64 bytes from 192.36.125.18: icmp_seq=0 ttl=251 time=131.873 ms
64 bytes from 192.36.125.18: icmp_seq=1 ttl=251 time=130.545 ms
^C
--- ping.sunet.se ping statistics ---
2 packets transmitted, 2 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 130.545/131.209/131.873/0.664 ms

The connection can be closed with the following command

AT_OWANCALL=1,0,0